Subaru Crosstrek Service Manual: Operation

1. SUBARU STARLINK CONNECTION ID DISPLAY

1. Turn the ignition switch to ACC.

2. Press the AUDIO/TUNE knob (b) five times with the HOME button (a) pressed to display the {Service Menu} screen.

3. Touch the {Product Information} (c) to display the {Product Information} screen.

4. Confirm the connectivity ID (16 digits).

1. Turn the ignition switch to ACC.

2. Press the AUDIO/TUNE knob (b) five times with the HOME button (a) pressed to display the {Service Menu} screen.

3. Touch the {Service Information} (c).

4. Touch the {Version Information} (d) to display the {Version Information} screen.

5. Touch the {AVN or DA} (e) to display the {Unit Version Information} screen.

6. Confirm the version.

1. Turn the ignition switch to ACC.

2. Press the HOME button to display the {HOME} screen.

3. Touch the {SETTINGS} to display the {SETTINGS} screen.

4. Touch the {General} to display the {General Setting} screen.

5. Touch the {Delete Personal Data}, and touch the {Delete}.

6. {Deleting personal date. Please do not turn the vehicle off.} is displayed, and all data deletion is initiated.

7. When all data is deleted, {Initialization Complete.} is displayed.

1. Turn the ignition switch to ACC.

2. Press the button (b) twice with the button (a) pressed.

Pressing the button (c) for 3 seconds or more, or turning the ignition switch from the OFF to ACC position can exit the diagnostic mode.

3. {Line Diag} screen is displayed.

4. Check the connection status with the {Connectivity Check} in the {Line Diag} screen.

GPS is displayed only for the navigation system.

Check the external connection terminals (USB 1, 2 and AUX) by connecting a memory for check or a pin jack.

1. Turn the ignition switch to ACC.

2. Press the button (b) twice with the button (a) pressed.

Pressing the button (c) for 3 seconds or more, or turning the ignition switch from the OFF to ACC position can exit the diagnostic mode.

3. {Line Diag} screen is displayed.

4. Check the connection status with the {Vehicle Signal Check} in the {Line Diag} screen.

GPS is displayed only for the navigation system.

• Check illumination

NOTE:

Make sure that the bright switch is not ON.

1. Turn the ignition to ON.

2. Set the lighting switch to the parking position.

3. Make sure that {ON} lights in ILL+ and then the screen becomes dim.

ON: Normal.

OFF: Abnormal. Check the signal line connector. If there are no problems, the unit could be faulty.

– Before starting inspections, check the safety around the vehicle.

– Lift up the vehicle as necessary.

– When the diagnostic trouble code is input in the VDC CM, perform the Clear Memory Mode.

1. Drive the vehicle at 9 km/h (6 MPH) or more.

2. Check that {ON} is displayed in SPD.

ON: Normal.

OFF: Vehicle speed is less than 7 km/h (4 MPH), or malfunction is detected in the signal line. Check the signal line connector. If there are no problems, the unit could be faulty.

1. Pull parking brake lever.

2. Check that {ON} is displayed in PKB.

ON: Normal.

OFF: Abnormal. Check the signal line connector. If there are no problems, the unit could be faulty.

Before starting inspections, check the safety behind the vehicle.

1. Turn the ignition to ON.

2. Pull the parking brake lever and depress the brake pedal, then place the select lever or gear shift lever in reverse.

3. Make sure that {ON} is displayed in REV.

ON: Normal.

OFF: Abnormal. Check the signal line connector. If there are no problems, the unit could be faulty.

1. Turn the ignition switch to ACC.

2. Press the button (b) twice with the button (a) pressed.

Pressing the button (c) for 3 seconds or more, or turning the ignition switch from the OFF to ACC position can exit the diagnostic mode.

3. {Line Diag} screen is displayed.

4. Touch {Audio Check} on the {Line Diag} screen.

5. {Audio Check} screen is displayed.

6. Touch the {ON} key of {Speaker Check} to check speaker output.

NOTE:

• The speaker front left > front right > rear right > rear left will sound in order for 2 seconds each.

• The speaker sounds at the maximum volume during speaker check.

• Press the {Return} key to return to the {Line Diag} screen.

Note

Rear accessory power supply socket

Other materials:

Reclining the seatback
Pull the reclining lever up and adjust the seatback to the desired position. Then release the lever and make sure the seatback is securely locked into place. The seatback placed in a reclined position can spring back upward with force when the lever is pulled. While operating the lever ...

Removal
GLASS/WINDOWS/MIRRORS > Power Window Control SwitchREMOVAL1. MAIN SWITCH1. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">2. Remove the trim panel - front door. Door Trim > REMOVAL">3. Remove the panel - power window main ...

Hazard warning flasher
Models without multi function display Models with multi function display The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works regardless of the position of the ignition switch. To ...