Subaru Crosstrek Service Manual: Dtc u0131 lost communication with power steering control module

DTC DETECTING CONDITION:

No data is received from power steering CM.

TROUBLE SYMPTOM:

Cooperation control with power steering CM does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0131 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0131 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the electric power steering data no-receive detected in several modules?

Replace the power steering CM. Power Steering Control Module">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 6.

6.REPLACE MODULE.

1) Replace the power steering CM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0131 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Reinstall the power steering CM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0131 a current malfunction?

Replace the power steering CM. Power Steering Control Module">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0131 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULE">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0126 lost communication with steering angle sensor module

Dtc u0140 lost communication with body control module

Other materials:

Rear window wiper blade assembly
1. Raise the wiper arm off the rear window. 2. Turn the wiper blade assembly counterclockwise. 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. 4. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 5. Hold the wiper arm ...

Disassembly
CONTROL SYSTEMS > Select LeverDISASSEMBLY1. GRIP ASSY1. Remove the button assembly_AT.(A)Claw2. Remove the rod COMPL.2. AT SELECT LEVER ASSEMBLY1. Remove the spacer plate.2. Remove the gasket.3. Insert a flat tip screwdriver with a thin tip under the connector and disconnect the harness connector ...

Installation
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)(H4DO) > EGR PipeINSTALLATION1. Temporarily install the EGR pipe to the intake manifold and water pipe assembly, and tighten the EGR pipe in numerical order as shown in the figure.NOTE:Use a new gasket.Tightening torque:6.4 N·m (0.7 kgf-m, 4. ...