Subaru Crosstrek Service Manual: Dtc c1741 pressure sensor

DTC detecting condition:

Defective pressure sensor

Trouble symptom:

• ABS does not operate.

• VDC does not operate.

• Hill start assist does not operate.

1.CHECK STOP LIGHT SWITCH CIRCUIT AND INSTALLATION CONDITION.

Check the stop light switch circuit and the installation condition.

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 2.

Repair the stop light switch circuit or correct the installation condition.

NOTE:

If there is malfunction in the stop light circuit, DTC may be recorded in the memory.

2.CHECK OUTPUT OF PRESSURE SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

2) Read the «Master Cylinder Pressure Sensor» displayed on display.

With the brake pedal released, does the value for «Master Cylinder Pressure Sensor» fall within 0 — 11 bar?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 3.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

3.CHECK OUTPUT OF PRESSURE SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

2) Read the «Master Cylinder Pressure Sensor» displayed on display.

When the brake pedal is operated, does the value of «Master Cylinder Pressure Sensor» change in accordance with the brake pedal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 4.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

4.CHECK VDCCM&H/U.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Perform the Inspection Mode. Inspection Mode">

3) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 5.

5.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c0073 abnormal lateral g sensor output

Dtc c1251 wheel speed sensor system

Other materials:

Assembly
WIPER AND WASHER SYSTEMS > Wiper BladeASSEMBLY1. FRONT1. Insert the rubber assembly - windshield wiper onto the blade - windshield wiper so that the stopper is in the position shown in the figure.2. Make sure the rubber assembly - windshield wiper is securely fastened to the pull stopper (a).2. R ...

Dtc p0108 manifold absolute pressure/barometric pressure sensor circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0108 MANIFOLD ABSOLUTE PRESSURE/BAROMETRIC PRESSURE SENSOR CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Cle ...

Installation
DRIVE SHAFT SYSTEM > Front Hub Unit BearingINSTALLATION1. Place the front brake back plate between the front axle housing and the front hub unit bearing, and tighten the bolt.CAUTION:• Do not get closer the tool which charged magnetism to magnetic encoder.• Be careful not to damage th ...