Subaru Crosstrek Service Manual: Keyless access with push button start system (diagnostics)
- Control module i/o signal
- Diagnostic procedure with diagnostic trouble code (dtc)
- Dtc u0100 lost communication with ecm/pcm a
- Dtc u1120 lost communication with autostart stop control module
- Dtc u0101 lost communication with tcm
- Dtc b1242 wireless tuner
- Dtc b2271 ign relay control circuit
- Dtc b2274 acc relay control circuit
- Dtc b2275 engine start request control circuit
- Dtc b2276 acc relay off signal
- Dtc u0122 lost communication with vehicle dynamics control module
- Dtc u0140 lost communication with body control module
- Dtc b2277 submerging circuit
- Dtc b2282 vehicle speed signal correlation
- Dtc b2283 vehicle speed sensor
- Dtc b2284 brake signal correlation
- Dtc b2285 steering lock position signal correlation
- Dtc b2286 engine speed signal(without auto start stop)
- Dtc b228a engine speed signal(with auto start stop)
- Dtc b2779 remote control engine starter collation
- Dtc b2781 steering lock cm control circuit
- Dtc b2782 steering lock drive request signal correlation
- Dtc b2784 antenna circuit (push engine switch)
- Dtc b2785 lin communication
- Dtc b2786 steering lock cm communication
- Dtc b2788 ign signal correlation (steering lock cm)
- Dtc b2789 id code box communication
- Dtc b2790 id code box circuit
- Dtc b278a push engine switch power supply circuit
- Dtc b278d id code box judgment circuit
- Dtc b27a1 driver side external antenna open
- Dtc b27a2 passenger side external antenna open
- Dtc b27a5 front internal antenna open
- Dtc b27a7 trunk/rear gate internal antenna open
- Dtc b27a8 trunk/rear gate external antenna open
- Dtc b1572 imm circuit except antenna circuit
- Dtc b1576 egi control module eeprom
- Dtc b1577 imm control module eeprom
- Dtc b1571 reference code incompatibility (immobilizer cm to ecm)
- Dtc u0155 lost communication with instrument panel cluster (ipc) control module
- Dtc u0401 invalid data received from ecm/pcm a
- Dtc u0422 invalid data received from body control module
- Dtc u0073 control module communication bus off
- General description
- Read current data
- Subaru select monitor
- Basic diagnostic procedure Procedure
- Check list for interview Check
- Clear memory mode Operation
- Diagnostics with phenomenon Inspection
- Electrical component location Location
- General diagnostic table Inspection
- Keyless access system check Operation
- List of diagnostic trouble code (dtc) List
- Read diagnostic trouble code (dtc) Operation
- System operation check mode Operation
Component
INTAKE (INDUCTION)(H4DO) > General DescriptionCOMPONENT(1)Air intake duct(8)Air cleaner case (rear)Tightening torque: N·m (kgf-m, ft-lb)(2)Clip(9)ClipT1:1 (0.1, 0.7)(3)Cushion(10)Mass air fl ...
Other materials:
Electrical specification
AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > Control Module I/O SignalELECTRICAL SPECIFICATION1. AUTO HEADLIGHT BEAM LEVELER CMContentTerminal No.Measuring conditionStandardIG power supply1 ←> Chassis groundIgnition switch ON8 — 16 VGND2 ←> Chassis groundAlwaysLess than 1 ...
Removal
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Fuel Filler PipeREMOVALWARNING:Place “NO OPEN FLAMES” signs near the working area.CAUTION:Be careful not to spill fuel.1. Release the fuel pressure. Fuel > PROCEDURE">2. Drain fuel. Fuel > PROCEDURE">3. Disconnect the groun ...
Basic operation
By operating "
" or "
" of the control
switch, the screens and selection items
can be switched. When the "
/SET"
switch is pulled toward you, the item can
be selected and set.
If there are some useful messages, such
as vehicle information, warning information,
etc., they wi ...
