Subaru Crosstrek Service Manual: Eyesight (diagnostics)
- Acc cancel code(s) display
- Control module i/o signal
- Diagnostic code(s) display
- Diagnostic procedure with diagnostic trouble code (dtc)
- Dtc u0100 lost communication with ecm/pcm a
- Dtc u0073 control module communication bus off
- Dtc u0101 lost communication with tcm
- Dtc b2801 tcm abnormal
- Dtc b2802 etc abnormal
- Dtc u0122 lost communication with vehicle dynamics control module
- Dtc u0140 lost communication with body control module
- Dtc b2806 ecm abnormal
- Dtc b2807 ecm abnormal
- Dtc b2809 vdc malfunction
- Dtc b280a vdc echo back disagreement
- Dtc b280b vdc brake fluid pressure
- Dtc b280f combination meter malfunction
- Dtc b2810 incompatible with eyesight (combination meter)
- Dtc b2814 power supply low voltage
- Dtc b2815 power supply high voltage
- Dtc b2817 brake lamp
- Dtc b28a0 vehicle model judgment
- Dtc b28a1 eyesight communication(ecm)
- Dtc b28a2 eyesight communication(vdc)
- Dtc b28a3 eyesight communication(meter)
- Dtc b28a5 engine torque limiter control prohibit
- Dtc b28a6 internal stereo camera communication 1
- Dtc b28a7 stereo camera recognition(target)
- Dtc b28a8 internal stereo camera communication 2
- Dtc b28a9 stereo camera synchronized recognition data
- Dtc b28aa stereo camera microcomputer 1
- Dtc b28ab stereo camera microcomputer 2
- Dtc b28ac stereo camera asic
- Dtc b28ad stereo camera image recognition
- Dtc b28ae internal stereo camera power supply
- Dtc b28af stereo camera adjustment incomplete
- Dtc b28b1 stereo camera automatic adjustment
- Dtc b28b2 stereo camera high temperature
- Dtc b28b3 stereo camera low temperature
- Dtc b28b5 +b circuit open
- Dtc b28b6 pre-collision off switch
- Dtc b28b7 ldp off switch
- Dtc b28b8 eyesight steering switch 1
- Dtc b28b9 eyesight steering switch 2
- Dtc u0155 lost communication with instrument panel cluster (ipc) control module
- Dtc u0401 invalid data received from ecm/pcm a
- Dtc u0402 invalid data received from tcm
- Dtc u0416 invalid data received from vehicle dynamics control module
- Dtc u0422 invalid data received from body control module
- Dtc u0423 invalid data received from instrument panel cluster control module
- Diagnostics with phenomenon
- Check eyesight steering switch
- Diagnostic procedure with phenomenon
- Check adaptive cruise control indicator light/constant speed cruise control indicator light and cruise set indicator light
- Ecm cancel code(s) display
- Eyesight temporary code(s) display
- Freeze frame data display
- General description
- Subaru select monitor
- Basic diagnostic procedure Procedure
- Check list for interview Check
- Clear memory mode Operation
- Electrical component location Location
- Read current data Operation
- Real-time diagnosis Operation
Ornament Installation
EXTERIOR/INTERIOR TRIM > OrnamentINSTALLATION1. LETTER MARKAlign the end of application tape with the end of panel, then adhere the letter mark.(a)Panel - rear gate end(b)Application tape end NOTE ...
Other materials:
Smart Rearview Mirror/compass with HomeLink
Safety precautions
WARNING
When driving the Subaru Ascent, never depend solely on the Smart Rearview
Mirror display. This system, although advanced, has inherent blind spots and
limitations, and it is essential to visually confirm surroundings before making
maneuvers. Always remain att ...
Installation
GLASS/WINDOWS/MIRRORS > Rear Quarter GlassINSTALLATION1. Fabricate the cartridge nozzle tip as shown and set the sealant gun with the adhesive.(1)10 mm (0.39 in)(2)8 mm (0.31 in)(3)Sealant gun2. Smoothen and clean the adhesive surfaces of the glass - rear quarter and body using the same procedure ...
Dtc b1695 door sensor lh failure
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1695 DOOR SENSOR LH FAILUREDIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:Front door impact sensor (LH) is faulty.If DTC AB is displayed, the circuit within the front door impact sensor (LH) i ...
