Subaru Crosstrek Service Manual: Operation

Subaru Crosstrek Service Manual / Instrumentation/driver info / Multi-function display (mfd) system / Operation

INSTRUMENTATION/DRIVER INFO > Multi-function Display (MFD) System

OPERATION

1. DIAGNOSTIC MODE (HIGH GRADE TYPE ONLY)

The settings of the multi-function display can be changed by performing the following procedures to display the diagnostic mode. To show the demonstration display only, refer to “DEMONSTRATION DISPLAY”.

CAUTION:

• To avoid battery discharge, perform the procedure while charging the battery.

• While performing the work, close the front hood and all doors, and do not operate any electrical parts.

• Display can not be switched to diagnostic mode if the illumination control dial is set to the position for the dimming cancel function (maximum brightness).

1. Procedure

CAUTION:

Perform the steps described in (2) through (4) within 10 seconds.

(1) Turn the ignition switch to ON, and within 3 seconds, turn the lighting switch to Switch 1 (TAIL/PARKING) or Switch 2 (HEAD).

(2) While keeping the lighting switch to Switch 1 (TAIL/PARKING) or Switch 2 (HEAD) position, press the MFD (ENTER) switch three times.

(3) Turn the lighting switch to OFF, and press the MFD (ENTER) switch three times.

(4) Turn the lighting switch to Switch 1 (TAIL/PARKING) or Switch 2 (HEAD) position again, and press the MFD (ENTER) switch three times.

NOTE:

• Except for the demonstration display setting of the diagnostic mode, the display will terminate by turning the ignition switch to OFF (ACC OFF) or by selecting “Back” from the menu screen.

• The demonstration display setting of the diagnostic mode will terminate by starting the engine or removing the battery. Even if the ignition switch is turned to OFF (ACC OFF), then to ON again, the diagnostic mode will not terminate.

• To select other menus from the demonstration display setting, terminate the diagnostic mode by starting the engine or removing the battery, then access to the diagnostic mode again.

2. Display menu

Change the display and settings from each menu.

Menu	Item	Content
Demonstration display setting	—	Shows demonstration display.
Vehicle status confirmation	• CAN communication	Displays the connection status of input signals.
	• U-ART communication
	• Camera connection
Customize	• Key operation sound	Select “ON” or “OFF”, then select “Set” to determine.
Customize	• Correction of lifetime fuel economy value*	Adjust the fuel economy value within the range of −10 — +10 km/l, then determine the value with MFD (ENTER) switch.
Back	—	Finish the diagnostic mode.

*: Correction of lifetime fuel economy value is used only when the multi-function display has been replaced. This function is provided as a compensation feature to bring the current lifetime fuel economy value to the one before the replacement of multi-function display.

2. DEMONSTRATION SCREEN DISPLAY (HIGH GRADE TYPE ONLY)

The demonstration screen can be displayed according to the following procedure.

CAUTION:

• Perform the steps while the ignition switch is OFF (ACC OFF).

• To avoid battery discharge, perform the operation under the following condition.

– Perform the operation while the battery is being charged.

– While performing the operation and displaying the demonstration mode, do not operate any electrical parts.

1. Procedure

CAUTION:

Perform the steps described in (2) through (5) within 10 seconds.

(1) Sit in the driver’s seat and close the door.

(2) Open the driver’s door, and within 5 seconds, press the MFD (ENTER) switch three times.

(3) Close the driver’s door, and press the MFD (ENTER) switch three times.

(4) Open the driver’s door, and press the MFD (ENTER) switch three times.

(5) Close the driver’s door, and press the MFD (ENTER) switch three times.

2. Go to “Demonstration screen display”.

NOTE:

The demonstration display will be cancelled in any of the following conditions.

• When 60 minutes elapsed since the demonstration mode started

• When the ignition switch is turned to ON

• When the MFD (ENTER) switch is turned to ON for two seconds

• When the battery voltage is low

3. ODO FUEL ECONOMY VALUE RESET (HIGH GRADE TYPE ONLY)

Follow the procedure below to initialize the ODO setting value.

1. Turn the ignition switch to ON, and press the MFD (ENTER) switch for two seconds.

2. Select “Factory delivery setting” from “Setting screen”.

3. Select “ODO setting reset” and determine with “Yes”.

4. The screen that indicates the completion of the setting is displayed for three seconds. This is the end of operation.

NOTE:

• The resetting operation is confirmed twice. Select confirmation according to the screen.

• The display will terminate by turning the ignition switch to OFF (ACC OFF) or by selecting “Back” from the menu screen.

Note

INSTRUMENTATION/DRIVER INFO > Multi-function Display (MFD) SystemNOTEFor procedure of each component in the Multi-Function Display (MFD) system, refer to the respective section.• Multi-functi ...

Relay and fuse

...

Other materials:

Installation
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)(H4DO) > CanisterINSTALLATION1. Install the canister to the vehicle using bolts and nuts.Tightening torque:7.5 N·m (0.8 kgf-m, 5.5 ft-lb)2. Install the drain tube (A), vent tube (B) and purge tube (C) to the canister.CAUTION:• Check tha ...

Economy history setting
1. Perform the preparation steps according to "Preparation for screen settings" 2. Operate the " " or " " switch to select the "Eco History" item. Then push the button. 3. Push the button once more. 4. Select the time of the logged fuel consumption history by o ...

Child restraint systems
Infants and small children should always be placed in an infant or child restraint system in the rear seat while riding in the vehicle. You should use an infant or child restraint system that meets Federal Motor Vehicle Safety Standards or Canada Motor Vehicle Safety Standards, is compatib ...