Subaru Crosstrek Service Manual: Dtc u1201 can-hs counter abnormal

DTC DETECTING CONDITION:

Communication is unstable because of high speed CAN communication error.

TROUBLE SYMPTOM:

• Display of combination meter indicates faulty.

• Control faulty may occur due to CAN communication error.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

1) Start the engine.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U0073 a current malfunction?

Perform the diagnosis of U0073. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0073 CONTROL MODULE COMMUNICATION BUS OFF">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U1201 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 4.

It is possible that temporary poor communication occurs. Perform the clear memory. Clear Memory Mode">

4.CHECK DTC.

1) Turn the ignition switch to ON.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U1201 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 5.

It is possible that temporary poor communication occurs. Perform the clear memory. Clear Memory Mode">

5.CHECK CONTROL MODULE.

1) Turn the ignition switch to OFF.

2) Disconnect the control modules other than body integrated unit in order.

NOTE:

When disconnecting ECM or VDC CM, connect resistance of 120 ? between CAN Hi and CAN Lo as an alternative of end resistance.

3) Turn the ignition switch to ON.

4) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is there any control module that U1201 is not detected as current malfunction?

Replace the control module.

Repeat 1) to 4) in step 5 until U1201 is not detected.

Dtc u1120 lost communication with autostart stop control module

Dtc u1235 lost communication with eyesight

Other materials:

Dtc p0017 crankshaft position - camshaft position correlation bank 1 sensor b
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0017 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 1 SENSOR BDTC detecting condition:Detected when two consecutive driving cycles with fault occur.Trouble symptom:• Engine stall• Improp ...

Dtc p0071 ambient air temperature sensor circuit "a" range/performance
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0071 AMBIENT AIR TEMPERATURE SENSOR CIRCUIT "A" RANGE/PERFORMANCEDTC detecting condition:Detected when two consecutive driving cycles with fault occur.CAUTION:After servicing or replacing faulty par ...

Dtc b1638 curtain airbag sensor lh initialization error
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1638 CURTAIN AIRBAG SENSOR LH INITIALIZATION ERRORDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Open or short circuit in harness of side sensor bus (LH)• Side airbag sensor (LH) ...