Subaru Crosstrek Service Manual: Basic diagnostic procedure Procedure

1. ENGINE

1.CHECK ENGINE START FAILURE.

1) Ask the customer when and how the trouble occurred using the interview check list. Check List for Interview > CHECK">

2) Start the engine.

Does the engine start?

Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.

Inspection using “Diagnostics for Engine Starting Failure” Diagnostics for Engine Starting Failure">

2.CHECK ILLUMINATION OF MALFUNCTION INDICATOR LIGHT.

Does the malfunction indicator light illuminate?

Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.

Inspection using “General Diagnostic Table”. General Diagnostic Table > INSPECTION">

3.CHECK COMMUNICATION STATUS.

1) Turn the ignition switch to OFF.

2) Connect the Subaru Select Monitor or general scan tool to the data link connector.

3) Turn the ignition switch to ON, and run the Subaru Select Monitor or general scan tool.

NOTE:

• Subaru Select Monitor

For detailed operation procedures, refer to the “Subaru Select Monitor”. Subaru Select Monitor">

• General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Does Subaru Select Monitor or general scan tool communicate with vehicle normally?

Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.

Inspection using “Diagnostic Procedure for Subaru Select Monitor Communication”. Diagnostic Procedure for Subaru Select Monitor Communication">

4.CHECK DTC.

Read DTC using Subaru Select Monitor or general scan tool.

NOTE:

• Subaru Select Monitor

For detailed operation procedures, refer to “Read Diagnostic Trouble Code (DTC)”. Read Diagnostic Trouble Code (DTC)">

• General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Is DTC displayed on Subaru Select Monitor or general scan tool?

Record DTC and freeze frame data, then repair the trouble cause. List of Diagnostic Trouble Code (DTC)"> After repair, go to the next step. Basic Diagnostic Procedure > PROCEDURE">Go to Step 5.

Repair the related parts.

NOTE:

If DTC is not shown on display although the malfunction indicator light illuminates, perform the diagnosis of malfunction indicator light circuit or combination meter. Malfunction Indicator Light">

5.PERFORM DIAGNOSIS.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Perform the Inspection Mode or Drive Cycle. Inspection Mode"> Drive Cycle">

Is DTC displayed on Subaru Select Monitor or general scan tool?

Inspect using “Diagnostic Procedure with Diagnostic Trouble Code (DTC)”. Diagnostic Procedure with Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Active test Operation

Check list for interview Check

Other materials:

Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Blower Resistor (Manual A/C Model)INSPECTION1. Check the resistance between resistor terminals.Preparation tool:Circuit testerTerminal No.StandardConnection diagram4 — 3Approx. 0.43 ?4 — 2Approx. 1.03 ?4 — 1Approx. 3 ?2. Replace the resistor if the ...

Component
CLUTCH SYSTEM > General DescriptionCOMPONENT1. CLUTCH ASSEMBLY(1)Dust cover(6)Release bearingTightening torque: N·m (kgf-m, ft-lb)(2)Lever spring(7)Clutch coverT1:16 (1.6, 11.8)(3)Pivot(8)Clutch discT2: Flywheel > INSTALLATION">(4)Release lever(9)Flexible flywheel (5)Clip(10)Pi ...

Refrigerant leak check Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Refrigerant Leak CheckINSPECTION1. Attach the manifold gauge set.Preparation tool:Manifold gauge set(1) Check that all valves are fully closed.(2) Install the low/high pressure hoses to the service ports on the low/high pressure sides of the vehicle resp ...