Subaru Crosstrek Service Manual: Replacement
DIFFERENTIALS > Differential Gear Oil
REPLACEMENT
CAUTION:
• Gear oil is extremely hot just after driving. Be wary of receiving burns.
• Be careful not to spill the differential gear oil on exhaust pipe. If gear oil is spilled, wipe it off completely.
1. Lift up the vehicle.
2. Remove the drain plug and filler plug, and drain the gear oil.
• T-type
(A) | Filler plug |
(B) | Drain plug |
• VA1-type
(A) | Filler plug |
(B) | Drain plug |
3. Install the drain plug.
NOTE:
• For the T-type, degrease the thread portion sufficiently and apply liquid gasket to the drain plug.
Liquid gasket:
THREE BOND 1105 (Part No. 004403010) or equivalent
• For VA1 type, use a new gasket.
Tightening torque:
T-type:
49 N·m (5.0 kgf-m, 36.1 ft-lb)
VA1-type:
50 N·m (5.1 kgf-m, 36.9 ft-lb)
4. Fill the differential carrier with gear oil to the bottom of filler plug.
NOTE:
Carefully refill gear oil while watching the level. Excessive or insufficient oil must be avoided.
Recommended gear oil:
General Description > SPECIFICATION">
Oil capacity:
0.8 L (0.8 US qt, 0.7 Imp qt)
• T-type
(A) | Filler plug |
(B) | Drain plug |
• VA1-type
(A) | Filler plug |
(B) | Drain plug |
5. Install the filler plug.
NOTE:
• For the T-type, degrease the thread portion sufficiently and apply liquid gasket to the filler plug.
Liquid gasket:
THREE BOND 1105 (Part No. 004403010) or equivalent
• For VA1 type, use a new gasket.
Tightening torque:
T-type:
49 N·m (5.0 kgf-m, 36.1 ft-lb)
VA1-type:
50 N·m (5.1 kgf-m, 36.9 ft-lb)
Inspection
DIFFERENTIALS > Differential Gear OilINSPECTION1. Lift up the vehicle.2. Remove the filler plug, and then check the gear oil. Replace the gear oil if it is contaminated, deteriorated or cloudy. Di ...
Other materials:
Component
WHEEL AND TIRE SYSTEM > General DescriptionCOMPONENT(1)Screw(4)TPMS & keyless entry control moduleTightening torque: N·m (kgf-m, ft-lb)(2)Transmitter (snap in type)(5)TPMS CMT1:1.4 (0.14, 1.0)(3)Valve T2:7.5 (0.76, 5.5) T3:13 (1.33, 9.6)(1)TPMS & keyless entry control module(2) ...
Installation
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Control Valve BodyINSTALLATION1. Clean the mating surface of valve cover and transmission side.CAUTION:When cleaning the mating surface of the transmission side, be careful not to allow any dust, foreign matter and used liquid gasket to enter the transm ...
Specification
LIGHTING SYSTEM > General DescriptionSPECIFICATIONNo.DescriptionCapacity and wattageType(1)HeadlightLow beam (halogen type)12 V — 55 WH11Low beam (HID type)12 V — 35 WD2RHigh beam12 V — 60 WHB3Front turn signal light12 V — 21 WWY21WParking light12 V — 5 WW5WSide marker light12 V — 5 W ...
